Macros_and_Config.txt

# NOTE: All of this is based on my printer, which is a Voron 2.4 300

# Basic movements to dock and undock probe
#   Get Probe
[gcode_macro Get_Probe]
gcode:
    G0 X46.3 Y305 Z20 F12000			#Spot above where the carriage magnets line up with the magprobe magnets 
						#	(with magprobe in the dock)
    G0 X46.3 Y305 Z2 F3600			#move -Z to where all the magnets pairs first fully grab onto each other
    G0 X46.3 Y290 Z2 F1800			#Move -Y so the probe is fully clear of the the arms of the dock
    G0 X46.3 Y290 Z20 F3600			#move +Z so any move from here clears the buildplate.

#   Dock Probe
[gcode_macro Dock_Probe]
gcode:
    G0 X46.3 Y290 z10 F12000			#Above +Z and forward -Y of where magprobe side cutouts line up with dock arms
						#	(allows build plate clearance for next downward move to line up magprobe to arms)
    G0 X46.3 Y290 Z2 F3600			#Location where the side cutouts of the magprobe line up with the front of dock arms
    G0 X46.3 Y305 Z2 F3600			#move the magprobe +Y into the dock, engaging the arms
    G0 X80 Y305 Z10 F1800			#move +X and +Z to disengage the magprobe from the carriage
    G0 X80 Y290 Z20 F3600			#Move +Z and -Y to a safe spot where further moves won't collide with dock

	
	
# My homing override, QGL, and Mesh settings **MAKE SURE TO HOME Y BEFORE X**
# NOTE: All of this is based on my printer, which is a Voron 2.4 300
[homing_override]
axes: z
set_position_z: 0
gcode:
    G90
    G0 Z5 F600	#Move up a little to clear
   
    G28 Y 		#Home Y before X with Mantis to avoid collision with front idlers
    G28 X
   
    ##	XY Location of the Z Endstop Switch
    ##	Update X0 and Y0 to your values (such as X157, Y305) after going through
    ##	Z Endstop Pin Location Definition step.
    #home on z pin at this location
    G0 X200 Y305 F3600 
   
    G28 Z
    G0 Z10 F1800
  
	#	Go to middle of bed for 300 build
    G0 X150 Y150 Z30 F3600
   
   
[quad_gantry_level]
##	Use QUAD_GANTRY_LEVEL to level a gantry.
##	Min & Max gantry corners - measure from nozzle at MIN (0,0) and 
##	MAX (250, 250), (300,300), or (350,350) depending on your printer size
##	to respective belt positions
	
##	Gantry Corners for 300mm Build
gantry_corners:
	-53,-13
	355,380

##	Probe points (this is where the nozzle is during probing, not where the probe actually is)
points:

#A little more in
	40,30
	40,225
	260,225
	260,30

speed: 300
horizontal_move_z: 5
retries: 5
retry_tolerance: 0.0075
max_adjust: 10


[bed_mesh]
speed: 200
horizontal_move_z: 5
probe_count: 5,5
fade_start: 1
fade_end: 15.0
split_delta_z: .025
move_check_distance: 5
mesh_pps: 0,0
algorithm: bicubic
relative_reference_index: 12
mesh_min: 25,50
mesh_max: 275,275