Qidi X Smart 3

[mendeste]

Hi Leadustin
great work well done
Would you have the Printer.cfg and macro for Qidi X Smart 3
it would save me alot time
if not I'll need to use the current one and clean it up

Cheers

[leadustin]

Hi Leadustin great work well done Would you have the Printer.cfg and macro for Qidi X Smart 3 it would save me alot time if not I'll need to use the current one and clean it up

Cheers

Hello mendeste,
I currently have nothing for the Smart 3. I would have a look at the weekend to see if I can do something about it

[mendeste]

Thank you You are a legend Regards

…

On Sat, 24 Aug 2024 at 7:34 AM, leadustin ***@***.***> wrote: Hi Leadustin great work well done Would you have the Printer.cfg and macro for Qidi X Smart 3 it would save me alot time if not I'll need to use the current one and clean it up Cheers Hello mendeste, I currently have nothing for the Smart 3. I would have a look at the weekend to see if I can do something about it — Reply to this email directly, view it on GitHub <#13 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BCIQLIU2IST4MG3NWJXUZY3ZS7BJ5AVCNFSM6AAAAABM5KFAFGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGMBXHEZDKNRUGI> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[leadustin]

Just out of curiosity, have you flashed your Smart 3 to Klipper 0.12 etc? Because if not, a new printer.cfg and the macros won't help much.

[mendeste]

Hi Leadustin not yet waiting on 32g emmc to arrive should be this week then let the fun begin :) Regards <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail> Virus-free.www.avg.com <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail> <#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>

…

On Sun, 25 Aug 2024 at 18:58, leadustin ***@***.***> wrote: Just out of curiosity, have you flashed your Smart 3 to Klipper 0.12 etc? Because if not, a new printer.cfg and the macros won't help much. — Reply to this email directly, view it on GitHub <#13 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BCIQLIQWV4FJA6HIAUINDG3ZTG2D3AVCNFSM6AAAAABM5KFAFGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGMBYG44DAMZZGM> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[mendeste]

Hi I've also got spare Extruder board So was going to keep the original board and emmc If anything went wrong I could always go back That's my backup plan 😀

…

On Sun, 25 Aug 2024 at 6:58 PM, leadustin ***@***.***> wrote: Just out of curiosity, have you flashed your Smart 3 to Klipper 0.12 etc? Because if not, a new printer.cfg and the macros won't help much. — Reply to this email directly, view it on GitHub <#13 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BCIQLIQWV4FJA6HIAUINDG3ZTG2D3AVCNFSM6AAAAABM5KFAFGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGMBYG44DAMZZGM> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[mendeste]

Sorry Also got K-Touch was going to use this as replacement screen

…

On Sun, 25 Aug 2024 at 6:58 PM, leadustin ***@***.***> wrote: Just out of curiosity, have you flashed your Smart 3 to Klipper 0.12 etc? Because if not, a new printer.cfg and the macros won't help much. — Reply to this email directly, view it on GitHub <#13 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BCIQLIQWV4FJA6HIAUINDG3ZTG2D3AVCNFSM6AAAAABM5KFAFGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGMBYG44DAMZZGM> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[leadustin]

Good luck with that. Remember that I have written this guide primarily for the Max-3 and Plus-3. However, you will find a customised printer.cfg and the macros folder in the download. The mainboard of the Smart 3 is identical to the other two printers. Only the chamber heater is missing. If you have any questions, please write

[mendeste]

Thank you
will let you know how i go :)

[mendeste]

Hi Leadustin
Everything installed used Fluidd instead of mainsail
Just got one problem, when I home it should home X91 and Y91, which the center of the build plate
But it homing to far down and across
Regards

[leadustin]

Hi Leadustin Everything installed used Fluidd instead of mainsail Just got one problem, when I home it should home X91 and Y91, which the center of the build plate But it homing to far down and across Regards

II have seen that the homing position is still at 140mm
You must make your settings accordingly in the sensorless_homing_override.cfg. You should change the following variables:

variable_x_backoff_distance: 11 # Distance in mm to back off from the X axis after homing.
variable_y_backoff_distance: 24 # Distance in mm to back off from the Y axis after homing.

variable_first_homed_axis: 'X'

variable_safe_z_enable: True # Enables/disables moving the printhead to a safe XY position before homing the Z axis.
variable_safe_x: 91
variable_safe_y: 91

If you have installed fluidd, you have to replace the client.cfg in the macro folder with the one from /home/mks/fluidd-config/client.cfg and adapt your personal changes. You must also check whether everything is entered accordingly in moonraker.conf. Please check in your printer.cfg whether the individual files are included correctly. You can also upload your printer.cfg and moonraker.conf here and I will check.

[mendeste]

Thank you
I'm bet confused get this from where /home/mks/fluidd-config/client.cfg ( Is this my original client.cfg file?
Regards

[leadustin]

Thank you I'm bet confused get this from where /home/mks/fluidd-config/client.cfg ( Is this my original client.cfg file? Regards

Yes, this is the original client.cfg. I have packed the one from Mainsail into the macros folder and included it in printer.cfg.

[mendeste]

Hi Leadustin
All working great after 4 attempts 🤪
Tried twice with fluidd but moonraker would not connect after reboot. So installed with mainsail config everything and need to comment out some entries.
Then once everything was working, I installed Fluidd using kiauh. Works great side by side with mainsail.
I only have one problem this come up while printing but does not effect the printer
Stepper driver 'stepper_y' is over-heating
But it’s not, same temperature as the other 2 stepper motors

[leadustin]

Hi Leadustin All working great after 4 attempts 🤪 Tried twice with fluidd but moonraker would not connect after reboot. So installed with mainsail config everything and need to comment out some entries. Then once everything was working, I installed Fluidd using kiauh. Works great side by side with mainsail. I only have one problem this come up while printing but does not effect the printer Stepper driver 'stepper_y' is over-heating But it’s not, same temperature as the other 2 stepper motors

I'm glad to hear that your conversion went well. However, I can't really help you with the temperature problem. It may be a cooling problem. Or the stepper has a hardware problem. Have you installed Klipper TMC Autotune? This can cause problems under certain circumstances.

[mendeste]

Hi Leadustin All good working great The temperature problem my fault forgot to plug in the mother board Fan See attached pictures Working with BBT K-Touch screen

…

On Sun, 1 Sep 2024 at 1:41 PM leadustin ***@***.***> wrote: Hi Leadustin All working great after 4 attempts 🤪 Tried twice with fluidd but moonraker would not connect after reboot. So installed with mainsail config everything and need to comment out some entries. Then once everything was working, I installed Fluidd using kiauh. Works great side by side with mainsail. I only have one problem this come up while printing but does not effect the printer Stepper driver 'stepper_y' is over-heating But it’s not, same temperature as the other 2 stepper motors I'm glad to hear that your conversion went well. However, I can't really help you with the temperature problem. It may be a cooling problem. Or the stepper has a hardware problem. Have you installed Klipper TMC Autotune? This can cause problems under certain circumstances. — Reply to this email directly, view it on GitHub <#13 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BCIQLIQ3HHYC4QBKURZCX43ZUKSJZAVCNFSM6AAAAABM5KFAFGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGMRTGE3TOOBXGY> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[mendeste]

[leadustin]

looks very good. Good job

[theclue]

Hi all,

I would also like to make the conversion to my x-Smart 3, I was just wondering if you perhaps can make an easier step-by-step sum-up of your debugging results about the homing issue. While trying to follow-up the thread, it's not totally clear to me I must admit.

Additionally, in your opinion, is the QIDI PSU powerful enough to power the Rpi3 used for alternative display (using a step-down ofc)? I would love a "all-in-case" solution for the conversion :)

[mendeste]

Hi leadustin
Just update everything going well
Even added nozzle wipe see picture

[theclue]

Howdy :)

I was wondering if you have some updated about the homing issue and about the Wifi. In other issues it seems Wifi won't work and I have not LAN on my setup actually...