From 34952cacb4b1814501a6d66ad0a7de00d6776a6c Mon Sep 17 00:00:00 2001 From: Kit Kennedy Date: Wed, 10 Apr 2024 21:10:28 -0700 Subject: [PATCH] some more small updates after readthru --- electrical/pcb/README.md | 6 ++++-- .../control_board/BOM/v2.0.3/bom_v2.0.3_board_ref_parts.csv | 2 +- 2 files changed, 5 insertions(+), 3 deletions(-) diff --git a/electrical/pcb/README.md b/electrical/pcb/README.md index 84215f5e..fe9a6cc3 100644 --- a/electrical/pcb/README.md +++ b/electrical/pcb/README.md @@ -259,6 +259,7 @@ You **may** use larger headers to fill all the holes in the U2 footprint, but it You will need to attach male headers to the PCA9685 daughter board, as shown in figure 3.23. Also, 5v power is provided to the PCA9685 through the two holes at the top of the U2 header. To connect these, I soldered 2 small wire leads on the PCA9685 daughter board, and then soldered them on to the motor board once I installed the PCA9685. TODO: update instructions with alternative to janky wire leads for PCA9685 + TODO: figure 3.28 is not very good | | @@ -338,7 +339,8 @@ Make sure to orient the connector in the proper direction, as indicated in the i First, wire the 6pos terminal block headers to the roboclaw boards, as indicated in figure 3.36. TODO: update the below and make sure it's correct -FOR v2.0.3, you should wire the pins in the J16,J17,J18 headers directly to the pins on the corresponding side of the roboclaw - it is a direct 1-to-1 mapping all the way down, with no wires crossed. + +For v2.0.3, you should wire the pins in the J16,J17,J18 headers directly to the pins on the corresponding side of the roboclaw - it is a direct 1-to-1 mapping all the way down, with no wires crossed. Do this for all three roboclaws. @@ -482,7 +484,7 @@ And now you're done with the assembly! Finally, we'll move on to testing and con |:-:| | Figure 4.8: Completed control board | -## 6. Testing the PCB and wiring for the drive motos +## 6. Testing the PCB and wiring for the drive motors Before we insert the wiring and PCBs into the mechanical assemblies, we'll test and configure the drive motors, wiring, and PCB. This allows us to fix these critical parts if something doesn't look right and allows us to move to running the software as soon as the rover is assembled. diff --git a/electrical/pcb/control_board/BOM/v2.0.3/bom_v2.0.3_board_ref_parts.csv b/electrical/pcb/control_board/BOM/v2.0.3/bom_v2.0.3_board_ref_parts.csv index 7fa9a0db..de028a43 100644 --- a/electrical/pcb/control_board/BOM/v2.0.3/bom_v2.0.3_board_ref_parts.csv +++ b/electrical/pcb/control_board/BOM/v2.0.3/bom_v2.0.3_board_ref_parts.csv @@ -14,7 +14,7 @@ alternative suppliers: - https://www.digikey.com/en/products/detail/phoenix-contact/5452096/5186808?s=N4IgTCBcDa4OxwLQEZkBYAMbEDkAiIAugL5A",JPL Robotics:277-11404-ND, A10,J7 J12 J15 J19,pwm header,3,4,TSW-104-07-F-T,TSW-104-07-F-T,https://www.digikey.com/en/products/detail/samtec-inc/TSW-104-07-F-T/6691937,,,JPL Robotics:SSW-104-01-F-T, A11,J20 J30,test pin header,2,4,PEC08SAAN,S1012E-08-ND,https://www.digikey.com/en/products/detail/sullins-connector-solutions/PEC08SAAN/859161?s=N4IgTCBcDaIAoFEDCAGAHAZQIJYHIgF0BfIA,,,Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical, -A12,J21,test pin header,1,1,PPTC102LFBN-RC,PPTC102LFBN-RC,https://www.digikey.com/en/products/detail/sullins-connector-solutions/PPTC102LFBN-RC/810216?s=N4IgTCBcDaIApwCoGECMAGMAZAYgIQDkBaAJWRAF0BfIA,,,JPL Robotics:PPTC102LFBN-RC, +A12,J21,interconnect header,1,1,PPTC102LFBN-RC,PPTC102LFBN-RC,https://www.digikey.com/en/products/detail/sullins-connector-solutions/PPTC102LFBN-RC/810216?s=N4IgTCBcDaIApwCoGECMAGMAZAYgIQDkBaAJWRAF0BfIA,,,JPL Robotics:PPTC102LFBN-RC, A13,J22 J23,rpi header,2,2,S9175-ND_rpi_breakout,S9175-ND,https://www.digikey.com/en/products/detail/sullins-connector-solutions/SBH11-PBPC-D20-ST-BK/1990068?s=N4IgTCBcDaIMoE4CMB2ArAWgHIBEQF0BfIA,,,JPL Robotics:S9175-ND, A14,J24,arduino header,1,2,6posheader,455-1708-ND,https://www.digikey.com/en/products/detail/jst-sales-america-inc/B6B-PH-K-S-LF-SN/926615?s=N4IgTCBcDaICwFYEFoCMB2ADADmQOQBEQBdAXyA,,,JPL Robotics:455-1708-ND, A15,J25,rpi i2c header,1,0,SSW-104-01-F-T,SSW-104-01-F-T-ND,https://www.digikey.com/en/products/detail/samtec-inc/SSW-104-01-F-T/7873826?s=N4IgTCBcDaIMpwOoFoCMAGALM9rkDFkAVEAXQF8g,,Added +1 of TSW-104-07-F-T. Needs cleanup in kicad files,JPL Robotics:SSW-104-01-F-T,